Home Forums SharewareOnSale Deals Discussion DVDFab Toolkit / Jul 19 2021

Viewing 15 posts - 1 through 15 (of 27 total)
  • Author
    Posts
  • #18219612 Reply | Quote
    Ashraf
    Keymaster

    Have something to say about DVDFab Toolkit? Say it here!

    Have suggestions, comments, or need help? Post it here! If you know of better software than DVDFab Toolkit, post it here! If you know of issues with DVDFab Toolkit, post it here! Share your knowledge with all of us. :-)

    #18219881 Reply | Quote
    Neil Cronje
    Guest

    Hi, Have followed instruction and registered with DVDFab.
    Downloaded and tried to install the program.
    I got the following message
    “The installation path is invalid”
    Repeat download and installation gives same error message.
    Your help will be appreciated
    Thanks
    Neil

    #18219948 Reply | Quote
    Miss Pita
    Guest

    [@Neil Cronje]
    Same here! Took a long time to get it downloaded/registered and now I can’t install it. Very frustrating!!

    #18220752 Reply | Quote
    Bill B
    Guest

    [ @Ashraf]
    I’ve downloaded it twice and same results as other 2 comments. Jump through all these convoluted steps and get nothing.

    #18220808 Reply | Quote
    fahad
    Guest

    It was installed, but the registration process is complicated. The registration has not been completed. The program has been deleted. Thank you for the time

    #18220905 Reply | Quote
    desertfox
    Guest

    Have followed instruction and registered with DVDFab.
    Downloaded and tried to install the program.
    I got the following message
    “The installation path is invalid”
    Repeat download and installation gives same error message.

    #18220935 Reply | Quote
    PaulF
    Guest

    869MWPJWNZOZ is considered on the registration page as invalid code!

    #18221188 Reply | Quote
    Mark
    Guest

    When I go to register the program, it says that the serial number is invalid.

    #18221269 Reply | Quote
    Reg Pellow
    Guest

    On attempt at Registration, message received : “Invalid Serial Number”

    #18221331 Reply | Quote
    Strega69
    Guest

    My serial number is considered on the registration page as invalid code! :(

    #18221493 Reply | Quote
    townie2
    Guest

    It worked fine for me, be sure to read and follow all directions, it’s rather long and a little complicated, you do NOT use initial Serial # to register the program, but to register on their site as a member, THEN you will get program serial #

    #18221505 Reply | Quote
    Tom Spencer
    Guest

    I Have followed instruction and registered with DVDFab.
    Downloaded and tried to install the program.
    I got the following message
    “The installation path is invalid”
    Repeat download and installation gives same error message.
    Your help will be appreciated

    #18221556 Reply | Quote
    Tsvamp
    Guest

    The installer in the download kept giving me “The installation Path is invalid” After I registered I went to their site and downloaded the newest installer from there and it worked. Try that but make sure you follow the instructions on how to activate the serial. You do it through their website not the application.

    #18221774 Reply | Quote
    pete s harris
    Guest

    download path is invalid ????

    #18221882 Reply | Quote
    Svend
    Guest

    Thanks for the program!
    The registration process is like breaking into Fort Knox, but I succeeded in the end.
    BUT, it does not work to install on any other drive than C: as the program at startup looks for something on C: that is not there.
    Had to reinstall on C. to make it work.
    You should do this again.

Viewing 15 posts - 1 through 15 (of 27 total)
Reply To: Reply #18220905 in DVDFab Toolkit / Jul 19 2021