- This topic has 11 replies, 1 voice, and was last updated 1 year ago by
.
-
Posts
-
Have something to say about DoYourClone 3? Say it here!
Have suggestions, comments, or need help? Post it here! If you know of better software than DoYourClone 3, post it here! If you know of issues with DoYourClone 3, post it here! Share your knowledge with all of us. :-)
Error “Failed to open partition or disk” as program starts. Activated but cannot find any disks on PC
Activation failed . Licence code has been used ??????
[@solly marks]
Same here, saying it’s used…[ @Ashraf] Where do I add the registration number? There is nothing in the bottom left hand corner. It’s not shown as not activated or activated but I did have version 2 that I had to uninstall first.
Posts from people who can’t get the code to activate fill this forum, but a post warning that Windows Black Lotus fix will break all bootable media doesn’t! Right. Trust this forum – not.
Activation Failed license code has been used
DY42H-TBXC7-FSUH9-HC5KP-N3N9YJust want to say activation using the serial shown on the download page, i.e. “DY42H-TBXC7-FSUH9-HC5KP-N3N9Y” was successful for me.
FYI to those of you getting activation code errorsm if you are using a VPN, turn it off. I was also getting an error but once I turned off the VPN, it was accepted and activated. This has happened to me a few times on new installations so, if you are ever having a problem with activtion and you are using a VPN, try turning it off as your first step in troubleshooting the issue.
Thank you for allowing me to test this.
Doyourclone Fails to build a USB bootable drive.
*Try USB
*USB 3 (USB DISK 3.0, G:)
Create bootable disk
Creating WinPE…
Exporting WinPE…
Operation failed. time: 00:02:21
OK
It fried my 14.4 GB Microcenter USB 3.1 flash drive.
Properties show 0 GB and Re Formatting will no longer complete.
Try ISO—-
*Create ISO C:\Users\larho\Desktop\Doyourclone.iso
Elapsed time: 00:00:07
Creating WinPE ISO…
Exporting WinPE ISO…
WinPE ISO has been successfully exported.The next step is to use Rufus 4.2.2074
I get this message:
ESP image detected
The ISO you have selected uses UEFI and is small enough to be written as an EFI System
Partition (ESP). Writing to an ESP, instead of writing to a generic data partition occupying
the whole disk, can be preferable for some types of installations.
Please select the mode that you want to use to write this image:
® Write in ISO Image mode (Recommended)- I USED !
O Write in ISO – ESP mode I DID NOT USE.Here are all the Rufus setup details:
Rufus 4.2.2074
Device Clone DISK (G:) [16 GB]
Boot selection Doyourclone.iso
Partition scheme GPT
Target system UEFI (non CSM)
Volume label Clone DISK
File system FAT32 (Default)
Cluster size 8192 bytes (Default)
*Quick format
I successfully used the Rufus USB boot drive and created a “Clone” of same size C:\ and all remaining drive partitions on drive. I checked the box to use Sector by sector copy option. I am very happy with the results.
Thanks again !More Testing by Larry K.
I tried a 8 GB USB2 Drive and tried create a bootable drive with DoYourClone.
The results came back as failed. So I went to “Disk Tool” and ran a repair.
It says “Repair Partition”
Begin Check partition “G”
The type of the file system is RAW.
CHKDSK is not available for RAW drives.
Check Finished.
In other words: I destroyed the second usb boot drive !
Please use the ISO file of DoYourClone along with rufus 4.2 from my above post !DY42H-TBXC7-FSUH9-HC5KP-N3N9Y is not working either. I dont have any VPN installed.
